SPRÁVY
Technická podpora pre STN v elektronickom formáte
Technická podpora pre STN v elektronickom formáte a služby STN-online
viac viac

DEMO verzia služby STN-online
Na tejto DEMO-verzii služby STN-online si môžete vyskúšať základnú prácu s normami v systéme STN-online
viac viac

Ponuka nových noriem
Nové normy vychádzajú vždy k prvému dňu v mesiaci.
viac viac

LINKY
Portál technických noriem > STN EN 12409+A1
Poslať linku stránky emailom Vytlačiť obsah stránky

STN EN 12409+A1



Pridať tlačenú formu normy do košíka:


Pridať elektronickú formu normy do košíka:




Označenie: STN EN 12409+A1
Slovenský názov: Plastárske a gumárske stroje. Stroje na tvarovanie za tepla. Bezpečnostné požiadavky (Konsolidovaný text)
Anglický názov:
Pôvodné označenie:
Dátum vydania: 1. 4. 2012
Dátum zrušenia:
Jazyk: EN
ICS: 83.200
Triediaci znak: 69 1701
Úroveň zapracovania: idt EN 12409:2008+A1:2011
Vestník: 03/12
Poplatok: Tlačená verzia: 18,90 € 


Elektronická verzia
  1. Bez možnosti tlače, prenosu textu a obrázkov: 17.01 €
  2. Bez možnosti tlače, s prenosom textu a obrázkov: 18.90 €
  3. S možnosťou tlače, prenosu textu a obrázkov: 24.57 €
Vestník harmonizácie: 5/12, 2/13,
Nariadenie vlády: 436/2008
Zmeny:
Nahradzujúce normy:
Nahradené normy: STN EN 12409:2009-04 (69 1701)
Poznámka vo Vestníku:
Predmet normy:



Obsah normy STN EN 12409+A1
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
4.1 General
4.2 Hazards relating to all units
4.2.1 Mechanical hazards
4.2.2 Hazards due to electrical energy
4.2.3 Hazards due to failure/malfunction of the control system
4.2.4 Hazards resulting from failure of an energy supply
4.2.5 Hazards due to failure/malfunction of pneumatic equipment
4.2.6 Hazards resulting from failure/malfunction of hydraulic equipment
4.2.7 Hazards resulting from inadequate emergency precautions
4.2.8 Hazards resulting from noise
4.2.9 Hazards resulting from inhalation of hazardous dusts, fumes or gases during normal operation
4.2.10 Hazards due to hot surfaces
4.2.11 Hazards due to unsuitable ergonomics
4.2.12 Hazards due to unexpected start up
4.2.13 Hazards arising when setting the machine
4.2.14 Hazards arising from access to finishing area during production
4.2.15 Hazards due to permanent means of access
4.2.16 Hazards due to laser devices
4.3 Specific hazards and danger zones relating to individual units
4.3.1 Continuous sheet unwind unit
4.3.2 Single sheet feed unit
4.3.3 Material intake
4.3.4 Conveying equipment
4.3.5 Heating, pre-heating and edge heating
4.3.6 Forming station
4.3.7 Finishing station
4.3.8 Stacking station
4.3.9 Discharge station
4.3.10 Residual sheet winding unit
4.3.11 Sheet cutting unit
5 Safety requirements and/or protective measures
5.1 General
5.2 General safety requirements and/or protective measures relating to all units
5.2.1 Access to danger zones
5.2.2 Electrical equipment
5.2.3 Unintended gravity fall of raised elements
5.2.4 Pneumatic equipment
5.2.5 Hydraulic equipment
5.2.6 Precautions for emergencies
5.2.7 Noise
5.2.8 Inhalation of hazardous dusts, fumes and gases
5.2.9 Hot surfaces
5.2.10 Ergonomics
5.2.11 Unexpected start up
5.2.12 Setting mode
5.2.13 Access during production
5.2.14 Laser devices
5.2.15 Permanent means of access
5.2.16 Common safeguarding system
5.2.17 Fixing systems of fixed guards
5.3 Specific safety requirements and/or protective measures relating to individual units
5.3.1 Continuous sheet unwind unit
5.3.2 Single sheet feed unit
5.3.3 Material intake
5.3.4 Conveying equipment
5.3.5 Heating, pre-heating and edge heating
5.3.6 Forming station
5.3.7 Finishing station
5.3.8 Stacking zone
5.3.9 Discharge station
5.3.10 Residual sheet winding unit
5.3.11 Sheet cutting unit
6 Verification of safety requirements and/or protective measures
7 Information for use
7.1 Marking on the machine
7.1.1 Minimum marking
7.1.2 Additional markings
7.2 Instruction manual
7.2.1 General requirements
7.2.2 Hot surfaces
7.2.3 Use of personal protective equipment
7.2.4 Noise declaration
7.2.5 Extraction of dusts, fumes or gases
7.2.6 Electrostatic phenomena
7.2.7 Manual handling
7.2.8 Fire prevention
7.2.9 Manual intervention at the stacking zone
7.2.10 Safe cleaning
7.2.11 Use of acknowledge switch
7.2.12 Inspection of electrical drives
7.2.13 Single sheet feed malfunction
7.2.14 Static holding load
Annex A (informative) Single sheet machine (alternatively material feed from single sheet magazine or continuous sheet roll)
Annex B (informative) Continuous sheet machine (combined forming and finishing)
Annex C (informative) Continuous sheet machine (separate forming and finishing)
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC
Bibliography